Numnuts HD conflicts

Stormdog · Jan 10, 2007, 04:12 AM

I have Athlon 64 3500+
MSI KL8n Neo 2 Platinum
Nvidia nforce 3 Chipset
1 GB Corsair Pro Series Extreme memory Speed 3200 LED
ATI Radeon 9800 XT 256MB DDR
Maxtor 6B1209
IBM Deskstar DTLA 307075

My problem is that - The Maxtor is my primary HD. When I try and hook
up the IBM as a slave - The Maxtor is not detected - I have check this in
the bios, while the bios will auto detect the IBM slave being there it will not "see" the
Maxtor. As soon as I unhook the IBM and reboot the sys sees the MAx no Prob..
- I have several other older HD (1) Maxtor 5T030H3 (2) Quantum Fireball LCT10
and I don't have any problem getting them to work. Does anybody have an
Idea here. I have looked at my jumper settings and they are what the MFG
said to set them at.

Hep me Sum buddy
JON
Mo' head City NC

PangingJr · Jan 10, 2007, 05:32 AM

make sure that both hard drives are correctly jumpered to run as "master" and "slave" devices, and
the both master and slave devices are attached to the IDE cable's master and slave connectors... the master connector is at the end of the IDE cable, and the slave connector is in the middle. also, try replacing the IDE cable.

otherwise, check the IDE cable, to see if it can be used in the Cable Select configuration, and then you may want to try using Cable Select... read more info below...

Configuration Using Cable Select
http://www.pcguide.com/ref/hdd/if/ide/confCS-c.html

BWX · Jan 10, 2007, 05:35 AM

On my last dual IDE HD combo I had to use cable select.. the master / slave configuration did not work.

Tipstaff · Jan 10, 2007, 03:40 PM

Quote:

Originally Posted by BWX

On my last dual IDE HD combo I had to use cable select.. the master / slave configuration did not work.

You'd be surprised at how common that is these days.

There is something else to consider. Some drives will have 3 standard settings, being Master, Slave, Cable Select, however some might have a 4th setting which would be a "Master with Slave drive".

I think Pangings idea is right on about changing the IDE cable. Infact, if you can, use an older 40 wire cable to see if that works. Depending on the age of the drive it may not work properly with 80 wire cable, especially newer 80 wire cable that has a notch out of one of the wires.

BWX · Jan 11, 2007, 12:17 AM

Yup.. that's why SATA is so nice.. IDE can be a pain with multiple drives on one channel- plus smaller cables.
Actually I still have 1 IDE, but soon I will be all SATA.

Stormdog · Jan 11, 2007, 11:28 PM

Thanks For Your Reply -
JON

Jan 10, 2007, 04:12 AM	#1
Stormdog DriverHeaven Newbie Join Date: Mar 2006 Location: Mo'Head City Norf Carelina Posts: 2 Rep Power: 0	Numnuts HD conflicts I have Athlon 64 3500+ MSI KL8n Neo 2 Platinum Nvidia nforce 3 Chipset 1 GB Corsair Pro Series Extreme memory Speed 3200 LED ATI Radeon 9800 XT 256MB DDR Maxtor 6B1209 IBM Deskstar DTLA 307075 My problem is that - The Maxtor is my primary HD. When I try and hook up the IBM as a slave - The Maxtor is not detected - I have check this in the bios, while the bios will auto detect the IBM slave being there it will not "see" the Maxtor. As soon as I unhook the IBM and reboot the sys sees the MAx no Prob.. - I have several other older HD (1) Maxtor 5T030H3 (2) Quantum Fireball LCT10 and I don't have any problem getting them to work. Does anybody have an Idea here. I have looked at my jumper settings and they are what the MFG said to set them at. Hep me Sum buddy JON Mo' head City NC

Jan 10, 2007, 05:35 AM	#3
BWX unplugged Join Date: Nov 2002 Location: USNY Posts: 19,669 Rep Power: 110 System Specs	On my last dual IDE HD combo I had to use cable select.. the master / slave configuration did not work. __________________

Jan 11, 2007, 12:17 AM	#5
BWX unplugged Join Date: Nov 2002 Location: USNY Posts: 19,669 Rep Power: 110 System Specs	Yup.. that's why SATA is so nice.. IDE can be a pain with multiple drives on one channel- plus smaller cables. Actually I still have 1 IDE, but soon I will be all SATA. __________________

Jan 10, 2007, 05:32 AM	#2
PangingJr Member Join Date: Mar 2003 Posts: 5,989 Rep Power: 71	make sure that both hard drives are correctly jumpered to run as "master" and "slave" devices, and the both master and slave devices are attached to the IDE cable's master and slave connectors... the master connector is at the end of the IDE cable, and the slave connector is in the middle. also, try replacing the IDE cable. otherwise, check the IDE cable, to see if it can be used in the Cable Select configuration, and then you may want to try using Cable Select... read more info below... Configuration Using Cable Select http://www.pcguide.com/ref/hdd/if/ide/confCS-c.html

Jan 11, 2007, 11:28 PM	Thread Starter #6
Stormdog DriverHeaven Newbie Join Date: Mar 2006 Location: Mo'Head City Norf Carelina Posts: 2 Rep Power: 0	Thanks For Your Reply - JON