hey guys...its me!! (anyway, i need help overhere..)

Kgentatszu] · May 9, 2004, 01:25 PM

hi everyone,
i know i know.....its been a while since i visted DH....sigh, i' havent been using me old PC since 5 months now, so ye cant blame me....(was so busy with life i guess....)
anyway, back to the topic......today is the first day i use me comp since 5 months now...yea....thats bad.~LOL BUt the problem is that i cant seem to OC now...=.=yeah wtf...a few hours ago, i felt like changing a better cooler before i start so i mounted an 900U to me old 2.6.....i unplugged everything before i mount it of course (and ye know what? that was me first time doing it) so i was wondering did i do anything wrong or what?
without the 900U i used to do 3.2 with the stock.....but after that i cant do nothing...when i OC a bit this showed up-----> "CPU OVER VOLTAGE, press F1 to go to setup and blah blah blah"
the thing is, i kind'a tried every combination but it wont work...damn!
so, maybe someone here could help...thankz in advance....
(oh yeah, if ye're curious, the Vcore in the bios reads 1.1643 that is when it says "overvoltage"..........@@'|||)

**MIG-31** · May 9, 2004, 01:49 PM

offtopic: welcome back didn't realise it has been so long.

Kgentatszu] · May 9, 2004, 02:37 PM

hey there johny~ hows life man??
by the way, speaking of me problems...it even shows the "over voltage thing" on stock voltages..well at least sometimes it would.........
for your information, before the 900U the temps are around 42 (idle).....now its 25..@@'|||
now did i just burn me CPU or did i do something wrong?

dipstick · May 9, 2004, 02:45 PM

That's weird man, not sure how the heatsink itself could cause this. First clear the CMOS if you haven't already and try OCing again. Also what thermal paste did you use? You make sure none of it got on the mobo-not even a super tiny drop? Did you change fans along with the new heatsink? Was the old fan getting power off the mobo? Is the new one hooked up the same?
Good to have ya back btw

Kgentatszu] · May 9, 2004, 02:48 PM

sorry to be the usual noob again......how to clear CMOS? thankz man...
and urmm...nope i dont think i'm that careless cause i put the thermal grease onto the chip itself instead of putting it on the Heatsink..side's i didnt use much...

dipstick · May 9, 2004, 02:56 PM

No worries bud

There should be a three pin jumper somewhere. Just move it over a pin for 30 seconds. You can also remove the battery for 5 minutes. What mobo you running?

Kgentatszu] · May 9, 2004, 02:57 PM

P4P800.....wheres the three pin anyway? and how do i remove the batteries?
hey could it be cause of i didnt plug the 20-pin panel accordingly? cause i sort'a "guess" when i plug it in....

dipstick · May 9, 2004, 03:02 PM

The CMOS jumper should be right by the battery itself. Turn off all power to the PC when doing this and remember you will clear everything in the BIOS so write thing down if need be. Leave on clear for 10-30 secs.
You can see it in this pic right over the battery. It the blue jumper
http://firingsquad.com/media/article...1268&pic_id=01

Kgentatszu] · May 9, 2004, 03:04 PM

okie...thankz i'll try it now....*fingers crossed*

Kgentatszu] · May 9, 2004, 03:14 PM

geez...it didnt work....i cleared the CMOS....but what do you know? right after the line ".......setup your time, date...." this follows "CPU over voltage error!"
and i have to set the Vcore to 1.5 to let it function properly..

Logla · May 9, 2004, 03:39 PM

Welcome back mate! Been a long time - we all missed you

Anyway - you might want to try and reflash the BIOS. Download the latest version from the mobo manufacturers website and follow the instructions they give you to flash it.

Kgentatszu] · May 9, 2004, 03:44 PM

dont think that would work (at least i think so cause the original ones did serve me good before today.....) will try it later though

Necrosis · May 9, 2004, 07:22 PM

Do you have your voltage set to "auto" or do you have it manually set?

Judas · May 10, 2004, 04:58 AM

Maxxypoos!!! Try flashing the bios.. check for newer updates.... try reseating EVERYTHING... try taking out unessary cards or hardware.. uplug hardrives cd-roms.....

Kgentatszu] · May 10, 2004, 07:04 AM

Quote:

Originally posted by Necrosis
Do you have your voltage set to "auto" or do you have it manually set?

i cant set it to auto....if i were to set it to auto again, the "overvoltage" thingy will pop up.........i'm now using 1.500V....

edit: now that i've tried....flashing the bios got me nowhere

May 9, 2004, 01:25 PM	#1
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	hey guys...its me!! (anyway, i need help overhere..) hi everyone, i know i know.....its been a while since i visted DH....sigh, i' havent been using me old PC since 5 months now, so ye cant blame me....(was so busy with life i guess....) anyway, back to the topic......today is the first day i use me comp since 5 months now...yea....thats bad.~LOL BUt the problem is that i cant seem to OC now...=.=yeah wtf...a few hours ago, i felt like changing a better cooler before i start so i mounted an 900U to me old 2.6.....i unplugged everything before i mount it of course (and ye know what? that was me first time doing it) so i was wondering did i do anything wrong or what? without the 900U i used to do 3.2 with the stock.....but after that i cant do nothing...when i OC a bit this showed up-----> "CPU OVER VOLTAGE, press F1 to go to setup and blah blah blah" the thing is, i kind'a tried every combination but it wont work...damn! so, maybe someone here could help...thankz in advance.... (oh yeah, if ye're curious, the Vcore in the bios reads 1.1643 that is when it says "overvoltage"..........@@'\|\|\|)

May 9, 2004, 01:49 PM	#2
MIG-31 HardwareHeaven News Mod Join Date: Dec 2002 Location: Nottingham,UK Posts: 56,860 Rep Power: 471 System Specs	offtopic: welcome back didn't realise it has been so long. __________________ Please Post Your News Submissions Here

May 9, 2004, 03:44 PM	Thread Starter #12
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	dont think that would work (at least i think so cause the original ones did serve me good before today.....) will try it later though Last edited by Kgentatszu]; May 9, 2004 at 04:15 PM.

May 9, 2004, 02:37 PM	Thread Starter #3
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	hey there johny~ hows life man?? by the way, speaking of me problems...it even shows the "over voltage thing" on stock voltages..well at least sometimes it would......... for your information, before the 900U the temps are around 42 (idle).....now its 25..@@'\|\|\| now did i just burn me CPU or did i do something wrong?

May 9, 2004, 02:45 PM	#4
dipstick HardwareHeaven Extreme Member Join Date: May 2002 Location: USA Posts: 3,609 Rep Power: 71 System Specs	That's weird man, not sure how the heatsink itself could cause this. First clear the CMOS if you haven't already and try OCing again. Also what thermal paste did you use? You make sure none of it got on the mobo-not even a super tiny drop? Did you change fans along with the new heatsink? Was the old fan getting power off the mobo? Is the new one hooked up the same? Good to have ya back btw

May 9, 2004, 02:48 PM	Thread Starter #5
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	sorry to be the usual noob again......how to clear CMOS? thankz man... and urmm...nope i dont think i'm that careless cause i put the thermal grease onto the chip itself instead of putting it on the Heatsink..side's i didnt use much...

May 9, 2004, 02:56 PM	#6
dipstick HardwareHeaven Extreme Member Join Date: May 2002 Location: USA Posts: 3,609 Rep Power: 71 System Specs	No worries bud There should be a three pin jumper somewhere. Just move it over a pin for 30 seconds. You can also remove the battery for 5 minutes. What mobo you running?

May 9, 2004, 02:57 PM	Thread Starter #7
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	P4P800.....wheres the three pin anyway? and how do i remove the batteries? hey could it be cause of i didnt plug the 20-pin panel accordingly? cause i sort'a "guess" when i plug it in....

May 9, 2004, 03:02 PM	#8
dipstick HardwareHeaven Extreme Member Join Date: May 2002 Location: USA Posts: 3,609 Rep Power: 71 System Specs	The CMOS jumper should be right by the battery itself. Turn off all power to the PC when doing this and remember you will clear everything in the BIOS so write thing down if need be. Leave on clear for 10-30 secs. You can see it in this pic right over the battery. It the blue jumper http://firingsquad.com/media/article...1268&pic_id=01

May 9, 2004, 03:04 PM	Thread Starter #9
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	okie...thankz i'll try it now....fingers crossed

May 9, 2004, 03:14 PM	Thread Starter #10
Kgentatszu] DriverHeaven Senior Member Join Date: Apr 2003 Location: Australia Posts: 1,802 Rep Power: 0	geez...it didnt work....i cleared the CMOS....but what do you know? right after the line ".......setup your time, date...." this follows "CPU over voltage error!" and i have to set the Vcore to 1.5 to let it function properly..

May 9, 2004, 03:39 PM	#11
Logla HardwareHeaven Extreme Member Join Date: May 2003 Posts: 3,311 Rep Power: 0	Welcome back mate! Been a long time - we all missed you Anyway - you might want to try and reflash the BIOS. Download the latest version from the mobo manufacturers website and follow the instructions they give you to flash it.

May 9, 2004, 07:22 PM	#13
Necrosis HardwareHeaven Extreme Member Join Date: May 2002 Location: Ohio Posts: 8,838 Rep Power: 131 System Specs	Do you have your voltage set to "auto" or do you have it manually set?